日本の寒地，北海道における2030年代の水稲生育への温暖化の影響予測とその対応(日语原文)

北海道では1980年代から2010年代まで，水稲圃場栽培期間である5–9月の気温は年代とともに上昇した。そこで，直近の2010年代（2010—2019年平均）と比べて， 2つの2030年代の予測気象から，既報の関係式より水稲生育を予測した。その結果，2030年代では2010年代に比べ，限界移植日（移植早限）が水稲栽培17地域の平均で8～9日早い。また，早限出穂期が1～5日早く，晩限出穂期が1～5日遅く，安全出穂期間が2～10日長い。出穂期は1～3日早い。出穂期から晩限出穂まで2～9日長いため，遅延型冷害の発生がやや少ない。生育期別気象は，出穂前24日以降30日間では生育が早いため平均気温が同じかやや低い。出穂前10日以降40日間および出穂期以降40日間では平均気温がやや高く，日射量はやや少ない。そのため，玄米収量は96～98％とやや低く，潜在収量性を示す気候登熟量示数は同じである。障害不稔発生に関係する穂ばらみ期冷害危険期の平均気温はわずかに低いかほぼ同じであるため，冷害発生の危険性は残る。一方，不稔発生をもたらす低温域の出現頻度には，地域間で差異がある。精米蛋白質含有率は同じであるが，アミロース含有率はやや低く，やや良食味である。米粒外観品質では被害粒歩合と着色粒歩合は一定の傾向がなく，未熟粒歩合はやや高い。精米白度は同じであるが，玄米白度はやや高い。以上の予測に対する技術的対応方向を示した。     

Comparative study of EICP treatment methods on the mechanical properties of sandy soil

This study analyzed the effect of different treatment methods in enzyme-induced carbonate precipitation (EICP) on the mechanical properties of soil. Soybean crude urease was used to catalyze the precipitation of calcium carbonate (CaCO₃). A multiple-phase method was proposed and further compared with commonly practiced EICP treatment methods (including the one-phase method, two-phase method, and premix-and-compact method) from the aspects of chemical conversion efficiency, CaCO₃ precipitation distribution, permeability, and unconfined compressive strength. Based on the findings, the characteristics of each method were further discussed and summarized. Although the enzymatic CaCO₃ precipitation generated from all the treatment methods could potentiate the soil strength to a great or less degree, using the proposed multiple-phase method could bring about a high chemical conversion efficiency, uniform distribution of CaCO₃ as well as preferable permeability retention. In addition, the multiple-phase method could significantly improve the efficiency of urease usage.     

配分工艺对中碳Ti-Mo高强Q&P钢组织和性能的影响

摘要：采用盐浴实验、扫描电镜、透射电镜、拉伸实验和磨损实验等手段，研究了配分工艺对中碳Ti Mo钢组织和性能的影响，分析了不同配分工艺处理下的组织演变和性能变化。结果表明，显微组织主要由回火马氏体、渗碳体、(Ti，Mo)C粒子组成。随着配分时间的延长和配分温度的升高，板条马氏体数量减少，马氏体板条厚度增加，边界钝化。此外，随着配分温度从310℃提高至400℃，抗拉强度、硬度和低温冲击韧性同时下降，分别降低约250MPa、56HV和15J。最后，Ms以下温度配分（310℃）试样的耐磨损性能明显优于Ms以上温度配分（400℃）试样。Ms以下温度配分试样磨损表面形貌以塑性变形为主，Ms以上温度配分试样磨损表面以犁沟为主。     

Site occupation and energy transfer in full color emitting phosphor Ba2Ca(BO3)2:Ce3+(K+),Eu2+,Mn2+

White light-emitting diodes (WLEDs) fabricated by single-phase full color emitting phosphor are an emerging solution for health lighting. The crystallographic site occupation of activators in a proper host lattice is crucial for sophisticated design of such phosphor. Here, we report a high quality white light-emitting phosphor Ba₂Ca(BO₃)₂:Ce³⁺(K⁺),Eu²⁺,Mn²⁺ with spectral distribution covering whole visible region. Blue light emission originates from Ce³⁺ ions occupying preferentially Ba²⁺ site by controlling synthesis conditions. Green and red lights are obtained from Eu²⁺ occupying Ba²⁺ (and Ca²⁺) site and Mn²⁺ occupying Ca²⁺ site, respectively. In this triple-doped phosphor, strong red emission with a low concentration of Mn²⁺ is realized by the efficient energy transfer from Ce³⁺ and Eu²⁺ to Mn²⁺. Furthermore, high quality white light is accomplished by properly tuning the relative doping amount of Ce³⁺(K⁺)/Eu²⁺/Mn²⁺ based on efficient simultaneous energy transfer. The results indicate that Ba₂Ca(BO₃)₂:Ce³⁺(K⁺),Eu²⁺,Mn²⁺ is a promising white light-emitting phosphor in WLEDs application.     

Microstructure and mechanical behavior of laser aided additive manufactured low carbon interstitial Fe49.5Mn30Co10Cr10C0.5 multicomponent alloy

Laser aided additive manufacturing(LAAM)was used to fabricate bulk Fe49.5Mn30Co10Cr10C0.5 interstitial multicomponent alloy using pre-alloyed powder.The room temperature yield strength(σy),ultimate tensile strength(σUTS)and elongation(εUST)were 645 MPa,917 MPa and 27.0％respectively.The as-built sample consisted of equiaxed and dendritic cellular structures formed by elemental segregation.These cellular structures together with oxide particle inclusions were deemed to strengthen the material.The other contributing components include dislocation strengthening,friction stress and grain bound-ary strengthening.The high εUTS was attributed to dislocation motion and activation of both twinning and transformation-induced plasticity(TWIP and TRIP).Tensile tests performed at-40℃and-130℃demonstrated superior tensile strength of 1041 MPa and 1267 MPa respectively.However,almost no twinning was observed in the fractured sample tested at-40℃and-130℃.Instead,higher fraction of strain-induced hexagonal close-packed(HCP)ε phase transformation of 21.2％were observed for fractured sample tested at-40℃,compared with 6.3％in fractured room temperature sample.     

梯度铝蜂窝夹芯板的力学行为

梯度分层铝合金蜂窝板是一种有效的吸能结构,本工作在梯度铝蜂窝结构的基础上根据梯度率的概念,通过改变蜂窝芯层的胞壁长度,设计了4种质量相同、梯度率不同的铝蜂窝夹芯结构。通过准静态压缩实验,并结合非线性有限元模拟准静态及冲击态下梯度铝蜂窝夹芯结构的变形情况及其力学性能,分析对比了相同质量下梯度铝蜂窝夹芯结构在准静态下的变形模式以及冲击载荷下分层均质蜂窝结构和不同梯度率的分层梯度蜂窝结构的动态响应和能量吸收特性。结果表明:在准静态压缩过程中,铝蜂窝梯度夹芯板的变形具有明显的局部化特征,蜂窝芯的变形为低密度优先变形直至密实,层级之间的密实化应变差随芯层密度的增大而逐渐减小;在高速冲击下,梯度蜂窝板并非严格按照准静态过程中逐级变形直至密实,而是在锤头冲击惯性及芯层密度的相互作用下整体发生的线弹性变形、弹性屈曲、塑性坍塌及密实化;另外,在本工作所设计的梯度率中,当梯度率为γ₁=0.0276时,梯度蜂窝夹芯板的吸能性达到最好,相较于同等质量下的均质蜂窝夹芯板,能量吸收提高了10.63%。     

Simulations of NBI fast ion loss in the presence of toroidal field ripple on EAST

NBI fast ion losses in the presence of the toroidal field ripple on EAST have been investigated by using the orbit code GYCAVA and the NBI code TGCO. The ripple effect was included in the upgraded version of the GYCAVA code. It is found that loss regions of NBI fast ions are mainly on the low field side near the edge in the presence of ripple. For co-current NBIs, the synergy effect of ripple and Coulomb collision on fast ion losses is dominant, and fast trapped ions located on the low field side are easily lost. The ripple well loss and the ripple stochastic loss of fast ions have been identified from the heat loads of co-current NBI fast ions. The ripple stochastic loss and the collisioninduced loss are much larger than the ripple well loss. Heat loads of lost fast ions are mainly localized on the right side of the radio frequency wave antennas from the inside view toward the first wall. For counter-current NBIs, the first orbit loss due to the magnetic drift is the dominant loss channel. In addition, fast ion loss fraction with ripple and collision for each NBI linearly increases with the effective charge number, which is related to the pitch angle scattering effect.     

Taylor Bubble Study of the Influence of Fluid Dynamics on Yield and Selectivity in Fast Gas-Liquid Reactions

A consecutive competitive gas-liquid reaction is investigated using a Taylor bubble setup regarding the influence of fluid mixing in the bubble wake on yield and selectivity. The concentration fields behind a Taylor bubble are visualized and measured quantitatively with a novel time-resolved absorption imaging technique based on Beer Lamberts law and an integral selectivity is derived. In addition, the calculation of the local selectivity, often used in numerical approaches, is discussed and the existing experimental limits for its derivation are pointed out. Finally, an increase in selectivity of a competitive consecutive reaction for enhanced mixing is experimentally confirmed.     

Reduced‐scale test to assess the effect of fire barriers on the flaming combustion of cored composites: An upholstery‐material case study

Herein, we describe a reduced‐scale test (“Cube” test), measuring the fire performance of specimens including a fire barrier (FB) and a flammable core material, which acts as the main fuel load. The specimen is intended to reproduce a cross‐section of a composite product where heat/mass transfer occurs primarily in a direction perpendicular to the FB. The Cube test procedure and benefits are discussed in this work by adopting residential upholstery furniture as an exemplary study. One flexible polyurethane foam, one polypropylene cover fabric, and 10 commercially available FBs were selected. They were used to compare the fire performance of FBs, measured in terms of peak of heat release rate, in the ASTM E1474‐14 standard test and the newly developed Cube test. Edge effects severely affected the performance of FBs in the ASTM E1474‐14 standard test but not in the Cube test. Furthermore, appropriate test conditions were determined in the Cube test to measure the so‐called “wetting point,” that is, the time and value of heat release rate measured when flammable liquid products were first observed on the bottom of the specimen. The relevance of the “wetting point” in terms of full‐scale fire performance and failure mechanism of FBs is discussed.